
Details
The new R07 CINCOM is compact and has a maximum machining diameter of ∅ 7 mm. It specializes in machining small-diameter parts, thus offering a wider range of high-precision work pieces for specialized parts.
The new R07 features a compact rotary guide bushing unit developed exclusively for high-speed, high-precision machining. With this new rotary guide bushing the R07 can perform metal cutting at speeds of up to 12,000 rpm. Without the rotary guide bushing the cutting speeds go up to 16,000 rpm. The sub-spindle delivers 10,000 rpm.
The R07 CINCOM uses linear motors to drive the slide and tool posts. This system achieves fast part processes with quick response and quiet operation, as well as eliminating thermal distortion. A scale feedback control system is also used with all axes, which offers the perfect machine configuration for machining small, high-precision parts.
Even while the high-speed built-in spindle motor is running at a high speed, the chuck can be opened or closed without first decreasing the speed. This feature reduces non-cutting idle time which results from acceleration and deceleration of the spindle. Use of two independent tool posts on the machine increases operation efficiency, eliminating idle time due to a tool exchange.
Complementing the R07 is the optional ALPS Automatic Bar Loader. This special bar loader is specifically designed to grasp and feed small wire-like bars into the machine.
The R07 CINCOM offers an optional vacuum type part removal system and carousel work piece separator that can greatly improve productivity.
Rotary tools are now part the gang tool post. This allows small-diameter parts requiring complex machining such as polygon turning and end face drilling be machined easily.
The R07 CINCOM with its use of a built-in spindle and linear motor, reduces the size of the machine foot print saving valuable floor space by 40% compared to that of the B12. This small, compact size considerably increases the manufacturing production area of the plant.
Standard NC functions
- NC unit dedicated to CINCOM R series
- Tool offset pairs: 16 pairs
- 7.2-inch monochrome liquid crystal display
- Product counter display: Up to 8 digits
- Operation time display
- Preparation function
- Interference check function
- On-machine program check function
- Main spindle speed change detection function
- Automatic power-off function
- Program storage capacity: Equivalent 20 m tape
- Thread cutting canned cycle
- Spindle synchronization control function
- Sub-inch command
Optional NC functions
- Main spindle 1 degree indexing function
- Back spindle 1 degree indexing function
- Multiple repetitive cycle
- Canned cycle for drilling
- Nose R compensation function
- Corner chamfering/rounding function
- Program storage capacity: Equivalent 120 m tape (maximum)
- Main spindle rigid tapping function
- Tool spindle rigid tapping function
- Back spindle rigid tapping function
- Continuous threading cycle
- Tool life control I
Standard Accessories
- Main spindle chucking device
- Workpiece separator
- Carry type synchronous rotary guide bushing device
- Coolant device (with level sensor)
- Door switch/door lock
- Back spindle chucking device
- Lubrication device (with level sensor)
Optional Accessories
- Stationary guide bushing device with open/close device
- Rotary tool spindle drive unit for gang tool
- Small 4-division separator
- Cut-off tool breakage detector
- Coolant flow-rate detecting device
- Signal lamp
- Work light
MACHINE SPECIFICATIONS
ITEM | R04 | R07 |
---|---|---|
Maximum machining diameter (D) | Ø4mm | Ø7mm |
Maximum machining length (L): Fixed guide bushing | 40mm | 40mm |
Maximum machining length (L): Rotary guide bushing | — | 40mm |
Maximum front drilling diameter | Ø3mm | Ø4mm |
Maximum front tapping diameter (tap) | M3 | M4 |
Spindle through-hole diameter | Ø9mm | Ø12mm |
Main spindle speed: Fixed guide bushing | 20,000 rpm (rating: 16,000 rpm) | 16,000 rpm |
Main spindle speed:Rotary guide bushing | — | 12,000 rpm |
For the gang rotary tool: Maximum drilling diameter | Ø2mm | Ø2mm |
For the gang rotary tool:Maximum tapping diameter | M2 | M2 |
For the gang rotary tool:Spindle speed | 8,000 rpm (part: 6,000 rpm) | 8,000 rpm (part: 6,000 rpm) |
Max. chuck diameter of back spindle | Ø4mm | Ø4mm |
Max. protrusion length in back machining process | 40mm | 40mm |
Max. drilling diameter in back machining process | Ø2mm | Ø2mm |
Max. tapping diameter in back machining process | M2.6 | M2.6 |
Back spindle speed | 10,000 rpm | 10,000 rpm |
Number of tools to be mounted | 13 | 13 |
Turning tools on the gang tool post | 5 | 5 |
Cross rotary tools on the gang tool post | 2 | 2 |
Tools for front drilling | 3 | 3 |
Tools for back drilling | 3 | 3 |
Tool size: Tool (gang tool post) | □8mm | □8mm |
Tool size: Sleeve | Ø15.875mm | Ø15.875mm |
Motors: Spindle drive | 0.75 / 1.1 kW | 0.75 / 1.1 kW |
Motors: Back spindle drive | 0.5 kW | 0.5 kW |
Motors: Tool spindle on the gang tool post | 0.2 kW | 0.2 kW |
Motors: Coolant oil | 0.18 kW | 0.18 kW |
Motors: Lubricating oil | 0.00 3kW | 0.00 3kW |
Center height | 1,000mm | 1,000mm |
Rated power consumption | 4kVA | 4kVA |
Weight | 950kg | 950kg |
R07 VI Floor Layout

Maximum height: 1,410 mm (55.51″) including mount
*A and L dimensions vary depending on bar feeder type
All specifications are subject to change without prior notice.
This product is subject to the export control laws of the United States and other countries. A license may be required prior to export, re-export or transfer of these products. Contact us for further information.